Ultipleat® High Flow XL Filter System product photo Primary L

Ultipleat® High Flow XL Filter System

Description

Ultipleat® High Flow XL filter is a large diameter, coreless, single open ended, pleated cartridge with an inside to outside flow pattern.

The spacing between the pleats within the filter has been optimized to deal with applications with moderate solids loadings. The filter's unique crescent-shaped pleat geometry, combined with its large 6-inch (15.24 mm) diameter and proprietary range of available Pall filter media, allows you to use significantly fewer filters and smaller housings for high flow rate applications.

Ultipleat® High Flow XL - SOE Cartridge Filter Benefits

  • Up to 50% smaller filter system possible
  • Up to 40 times fewer elements to change out
  • Higher flow rates per filter cartridge - up to 500 GPM (1900 lpm)
  • Available in 20-inch (508 mm), 40-inch (1016 mm) and 60-inch (1524 mm) lengths
  • Coreless, all plastic construction to minimize waste disposal
  • Absolute rated filter medium for reproducible performance
  • Inside to outside flow configuration - all debris within the filter
  • Polypropylene filters are made from all FDA listed materials
  • Long service life in moderate solids loadings applications


Contact Us
* Required

Documents

Datasheets

Download: English

Description

Description

Ultipleat® High Flow XL filter is a large diameter, coreless, single open ended, pleated cartridge with an inside to outside flow pattern.

The spacing between the pleats within the filter has been optimized to deal with applications with moderate solids loadings. The filter's unique crescent-shaped pleat geometry, combined with its large 6-inch (15.24 mm) diameter and proprietary range of available Pall filter media, allows you to use significantly fewer filters and smaller housings for high flow rate applications.

Ultipleat® High Flow XL - SOE Cartridge Filter Benefits

  • Up to 50% smaller filter system possible
  • Up to 40 times fewer elements to change out
  • Higher flow rates per filter cartridge - up to 500 GPM (1900 lpm)
  • Available in 20-inch (508 mm), 40-inch (1016 mm) and 60-inch (1524 mm) lengths
  • Coreless, all plastic construction to minimize waste disposal
  • Absolute rated filter medium for reproducible performance
  • Inside to outside flow configuration - all debris within the filter
  • Polypropylene filters are made from all FDA listed materials
  • Long service life in moderate solids loadings applications

Specifications

Materials of Construction

 
Filter Medium TypeFilter MediumSupport/Drainage MaterialsEnd CapsWrap
Materials
         
Ultipor® GF Glass Fiber Polyester/Nylon Glass Filled Acetal Polyester and
Polyamide Hotmelt
 
 

Operating Conditions2


 
Glass Fiber Medium
   
Maximum Differential Pressure1
(normal inside to outside flow)
50 psid at 250°F
3.44 bar at 121°C
 

1 For fluids compatible with the filter element at the stated temperature

2 Maximum temperature in aqueous system is 140°F/60°C
 

Horizontal Housings


Horizontal Housings, Centerpipe Design

Performance

Housing Design

Three configurations are available: horizontal, vertical and centerpipe design.

The in-line horizontal configuration eliminates the need for a platform, or ladder, to remove the filters from the housing.

Vertical vessels may be more appropriate when floor space is limited. However, a platform may be needed to easily remove the elements.

In both the standard horizontal and vertical configurations, the inlet pipe is located between the filter element tubesheet and housing lid. The larger the vessel diameter, the longer the distance to reach in and remove the elements from the vessel. In a centerpipe vessel the housing lid is closer to the filter tubesheet. When the lid is opened the filters are easily accessible for installation and removal. Centerpipe vessels are larger in diameter, and more costly.

  • Designed to the ASME, section VIII, division 1 code
  • Maximum differential pressure across tubesheet: 75 psid (5.17 bar) maximum
  • Standard housing gasket: spiral wound 304 stainless steel mineral fiber
  • Carbon steel exterior surfaces: sandblasted and coated with an inorganic zinc
  • Vent and drains: 1 inch FNPT
  • Corrosion allowance: 1/8 inch

Housing Ratings

 
Vessel MaterialTubesheet and Hold Down Plate
Material of Construction
Pressure Rating in
Psig/Bar g at 140°F / 60°C
     
Carbon steel 304 stainless steel 275 psig (18.95 bar)
     
304 stainless steel 304 stainless steel 259 psig (17.85 bar)
     
304L stainless steel 304L stainless steel 216 psig (14.89 bar)
     
316 stainless steel 316 stainless steel 261 psig (17.99 psig)
     
316L stainless steel 316L stainless steel 216 psig (14.89 psig)
 


Figure 1: Ultipleat High Flow Horizontal Housings (Aqueous Housing Pressure Drop - PSID)

Type

Large Format Filters

Ordering Information

Ordering Information/Specifications

Filter Cartridge Part Number: HFU  

 
Code
 
Filter Dimensions, Inches
(nominal)
Suggested Maximum Flow Per Cartridge-
GPM/LPM/MGD of Water
     
620 6" Diameter by 20" Long 175/663/0.25
     
640 6" Diameter by 40" Long 350/1325/0.5
     
660 6" Diameter by 60" Long 500/1900/0.7
 


 
Medium TypeCode
Absolute Liquid Removal Rating
(Microns) at 99.9% Efficiency by Particle Count1
Element Pressure Drop2 20 inch length (PSID/GPM)/
(MBar/M3/H)
Element Pressure Drop2 40 inch length (PSID/GPM)/
(MBar/M3/H)
Element Pressure Drop2 60 inch length
(PSID/GPM)/(MBar/M3/H)
           
Ultipor® GF Medium-XL HGF100  10.0 0.0029/0.88 0.0014/0.425 0.001/0.304
 

1 The test procedure used is an adaptation of ISO 4572, modified to determine the micron size above which particles are quantitatively removed.

2 Pressure drop in PSID per GPM for the cartridge length shown. Multiply this value by the total system flow to determine the aqueous pressure drop. Next for fluids other than water, multiply this value by the fluids viscosity at the operating temperature in centipoise. This value is the pressure drop across the Ultipleat High Flow filter(s) only; it must be added to the pressure drop due to the Ultipleat High Flow filter housing.

 

 
Code-Filter O-Ring Material
   
H13 (Standard for glass fiber filters) Buna N
   
H13U1 Buna N U-Cup
   
J (Standard for polypropylene filters) Ethylene Propylene
   
JU1 Ethylene Propylene U-Cup
   
H4 Silicone
   
H Fluorocarbon Elastomer
 
1 U-Cup seal should be deployed in those applications where ease of element removal is of paramount concern.

 

Ordering Information-Standard Horizontal and Vertical Housings

 
Part NumberNo. of FiltersRated Flow Per Housing-GPM/
LPM 60" Long Filter
Nominal Housing Diameter (In/mm)
(D)
Inlet/
Outlet Flange Diameter (In/mm)
Maxiumum
Horizontal Housing Overall Length (In/mm)
(L)
           
1HF   0804F1 1 500/1893 8 5/8 / 219.1 4/101.6 89/2261
           
2HF  1606F1 2 1000/3785 16/406.4 6/152.4 100/2527
           
3HF  1808F1 3 1500/5680 18/457.2 8/203.2 104/2642
           
4HF  2008F1 4 2000/7570 20/508 8/203.2 105/2654
           
7HF  2412F1 7 3500/13248 24/609.6 12/304.8 112/2832
           
12HF  3016F1 12 6000/22710 30/762 16/406.4 121/3073
           
19HF  3620F1 19 9500/35958 36/914.4 20/508 129/3264
 


 
Part NumberHorizontal Housing Height (In/mm)
(H)
Distance Between Housing and Lid and Tube-
sheet (In/mm)
Housing Weight Empty (Lbs/KG)Housing Weight Full of Water (Lbs/KG)Housing Cover Swing Opening (In/mm)
           
1HF   0804F1 32/817 14.5/368.3 471/214 621/282 9/228.6
           
2HF   1606F1 40/1023 22.7/576.3 1172/532 1771/803 25.77/654.6
           
3HF  1808F1 43/1093 26.2/665.2 1583/718 2384/1081 27.28/692.8
           
4HF  2008F1 46/1175 26.38/669.6 2087/947 3048/1382 29.77/756.3
           
7HF  2412F1 59/1487 31.88/809.6 3250/1474 4762/2160 34.28/870.6
           
12HF  3016F1 58/1480 38.69/982.7 4670/2118 7306/3314 37.99/964.9
           
19HF  3620F1 68/1718 43.37/1101.6 7060/3202 11121/5045 44.83/1138.8
 


Ordering Information - Horizontal Orientation, Centerpipe Designed Housings


 
Part NumberNo. of FiltersRated Flow Per Housing-GPM/
LPM 60" Long
Filter
Nominal Housing Diameter (In/mm)
(D)
Inlet/
Outlet Flange Diameter (In/mm)
Maximum
Horizontal Housing Overall Length (In/mm)
(L)
           
7HFC2808F1 7 3500/13248 28/711 8/203.2 104.3/2648
           
8HFC3012F1 8 4000/15140 30/762 12/304 117.6/2988
 


 
Part NumberHorizontal Housing Height (In/mm)
(H)
Distance Between Housing and Lid and Tube-
sheet (In/mm)
Housing Weight Empty (Lbs/KG)Housing Weight Full of Water (Lbs/KG)Housing Cover Swing Opening (In/mm)
           
7HFC2808F1 57/1448 4.9/124 4056/1840 6229/2825 36/914
           
8HFC3012F1 58 1/4 / 1480 6.1/154 4707/2135 7348/3333 40.06/1018
 


 
Code
Housing Configuration
   
H Horizontal
   
V Vertical
 


 
Code
Nominal Cartridge Length
(Inches/mm)
   
2 20/508
   
4 40/1016
   
6 60/1524
 


 
Code
 
Housing Metallurgy
   
285 Carbon Steel Vessel, 304 Stainless Steel Tubesheet
   
S3 304L Stainless Steel
   
S8 304 Stainless Steel
   
L3 316L Stainless Steel
   
L8 316 Stainless Steel
 
 
Code
 1
Optional Outlet Style
Horizontal Housings
   
XU Upper Outlet Location
   
XL Lower Outlet Location

Reviews

We appreciate your review of this product. Please login to your account to leave a review.