HYDRO-GUARD® PPB Series Backflushable Filter Cartridges product photo Primary L

HYDRO-GUARD® PPB Series Regenerable Backflush Filters

The Most Extensively Used Backflushable Pleated

Filter in Power Plant Condensate

  • Backflushable Pleated Filter Designed Specifically for Use in Power Plants
  • The Hydro-Guard PPB is Used in Condensate With or Without Resin Precoat
  • Constructed With the Highest Purity Materials (no fillers, talcs, TiO2 or surfactants) for Minimal Rinse-up Time
  • Surface Area Exceeds That of Conventional Condensate Filters by a 20:1 ratio for Lower Pressure Drops, Increased Filter Life and Longer Backflush Cycles
  • Eliminates Costs Associated with Use and Disposal of Powdered Resins
  • Iron Oxide and Suspended Copper are Typically Reduced by 98%+
  • Absolute Construction and Surface Retention for Efficient Backflushing and Particle Removal


Contact Us
* Required

Documents

Datasheets

Download: English

Description

The Most Extensively Used Backflushable Pleated

Filter in Power Plant Condensate

  • Backflushable Pleated Filter Designed Specifically for Use in Power Plants
  • The Hydro-Guard PPB is Used in Condensate With or Without Resin Precoat
  • Constructed With the Highest Purity Materials (no fillers, talcs, TiO2 or surfactants) for Minimal Rinse-up Time
  • Surface Area Exceeds That of Conventional Condensate Filters by a 20:1 ratio for Lower Pressure Drops, Increased Filter Life and Longer Backflush Cycles
  • Eliminates Costs Associated with Use and Disposal of Powdered Resins
  • Iron Oxide and Suspended Copper are Typically Reduced by 98%+
  • Absolute Construction and Surface Retention for Efficient Backflushing and Particle Removal

Specifications

Performance Specifications

Maximum Operating Temperature:

180°F (82.2°C)

Maximum Differential Pressure:

40 psid (2.8 bar) @ 150°F (65°C)
 
Product Feature Product Benefit Customer Benefit
Backflushable filter element Longer on stream life
Reduced number of filter changeouts
Lower disposal costs
Reduced personnel exposure to
radiation during filter changeouts
High surface area Longer run times
Higher dirt holding capacity
Lower operating costs
Fewer backflushes for reduced
disposal costs
All Polypropylene Virtually no extractables
Incinerable
Radiation Resistant
No rinse-up required
Concerns eliminated with regard to
chemistry changes
Reduced startup costs (i.e. downtime
rinse-up water, etc.)
Modular design High structural integrity Easy retrofit into existing pressure
vessels
Absolute Construction Highly efficient particle removal Less damage from iron and copper in
boiler and turbine
Quicker plant startups
Fewer boiler cleanings
 

Product Specifications

Materials of Construction

 
Filter Media: Polypropylene
Support Material: Polypropylene
Hardware: Polypropylene
Sealing: Thermal Bond
Gasket/O-ring Materials: EPDM (standard), Others available
 

Performance

Pressure Drop/Flow Data

 
Model Delta Pressure ΔP = (k) (Flow Rate)
HGPPB1 Δ = (0.50) Flow Rate
HGPPB2 Δ = (0.40) Flow Rate
HGPPB4 Δ = (0.05) Flow Rate
HGPPB10 Δ = (0.03) Flow Rate
HGPPB18 Δ = (0.01) Flow Rate
HGPPB42 Δ = (0.01) Flow Rate
 
This information is with water at ambient temperatures. Differential pressures are in PSID based on flow in GPM through a 10" (25.4 cm) element.

Type

Filter Cartridges

Ordering Information

Part Numbers/Ordering Information

* Based on typical application usage.
** For details, contact Pall Corporation.
1 - Registered trademark of DuPont Dow.

Part Numbers/Ordering Information

HGPPB (e.g. HGPPB–2–70–P–E–DOE)

 
Code Filter Grades*
1 1 μm
2 2 μm
4 4 μm
10 10 μm
18 18 μm
42 42 μm
 
* Based on typical application usage. ** For details, contact Pall Corporation. 1 - Registered trademark of DuPont Dow.
 
Code Cartridge Lengths (nominal)*
10 10" (25.4 cm)
20 20" (50.8 cm)
30 30" (76.2 cm)
40 40" (102 cm)
50 50" (127 cm)
60 60" (152.4 cm)
70 70" (178 cm)
80 80" (203.2 cm)
 
 
Code Gasket/O-ring Materials
S Silicone
N Buna N
V Viton1 A
E/td> EPDM
 
 
Code End Configurations
DOE DOE with elastomer gasket seal and endcaps
M3 SOE flat closed end, external 222 O-rings (retrofits other manufacturers’ Code 0)**
M6 SOE flat closed end, external 226 O-rings (retrofits other manufacturers’ Code 6)**
M7 SOE fin end, external 226 O-rings (retrofits other manufacturers’ Code 7)**
M8 SOE fin end, external 222 O-rings (retrofits other manufacturers’ Code 5)**
COOP Fine thread direct screw in
TVO Extended neck for better sealing
PAK Easy installation and removal; double seals for high integrity
PEA Retrofit for 2" (5.1 cm) seat cups
AERO Connects directly to tube sheet without additional hardware
 

Reviews

We appreciate your review of this product. Please login to your account to leave a review.