DFT Classic® Fluoropolymer Series Filter Cartridges product photo Primary L

DFT Classic® Fluoropolymer Series Filter Cartridges

Depth Filters for Aggressive and High Temperature Fluids

  • All PTFE construction for compatibility with a wide range of process fluids
  • Available in retention ratings of 0.5, 1, 3, 10, or 25 microns (μm)
  • Fits into most standard housings
  • May be used as a final filter in many applications, or to provide superior protection for membrane final filters
  • PVDF and PFA housings are available for use in all fluoropolymer filtration systems
  • M31 or DOE end configurations are available as standard products
1 Modified M3 end cap configuration features single 222 O-ring; M3 equivalent to Pall Code 3.


* Required
Need Help?
Download Datasheet
Description

Depth Filters for Aggressive and High Temperature Fluids

  • All PTFE construction for compatibility with a wide range of process fluids
  • Available in retention ratings of 0.5, 1, 3, 10, or 25 microns (μm)
  • Fits into most standard housings
  • May be used as a final filter in many applications, or to provide superior protection for membrane final filters
  • PVDF and PFA housings are available for use in all fluoropolymer filtration systems
  • M31 or DOE end configurations are available as standard products
1 Modified M3 end cap configuration features single 222 O-ring; M3 equivalent to Pall Code 3.
Applications

Applications

  • Acid etch systems - including Piranha Etch Solvent Strip applications
  • Most aggressive and/or high temperature acids or solvents

Recirculating Applications

Retention ratings, by convention, are for single pass applications. Many applications involve recirculating systems, where the filter media has several opportunities to capture contaminant. For example, in a 15.1 liter (4 gallon) system circulating at 7.6 lpm (2 gpm), the fluid passes through the filter cartridge five times in ten minutes. Thus, the effective retention of a filter cartridge is much finer. Specifically, a cartridge rated at 0.5 μm (nominal) on a single pass is often an effective 0.2 μm (nominal) filter on a recirculating basis.

Multi-Pass

Multi-Pass
Specifications

Performance Specifications

Filter grades

0.5, 1, 3, 10, 25 μm

Maximum operating temperature

PTFE is broadly compatible with many chemicals up to 185°C (365°F)2

Product Specifications

Materials of construction

 
Filter media: PTFE (fluoropolymer)
Center core: PTFE
222 O-ring: FEP encapsulated fluorocarbon elastomer (standard)
 

Dimensions (nominal)

 
Outside diameter:
  • 6.35 cm (2.5 in.), DOE only
  • 7.14 cm (2.81 in.), M3 only
Lengths: 25.4 cm (10 in.), 50.8 cm (20 in.), 76.2 cm (30 in.)
 

Additional High Temperature Materials

Pall can also supply DFT Classic filter cartridges in polyphenylene sulfide (PPS) for high temperature and aggressive applications. Additional PTFE products are also available, including the Fluoryte™ Series filter cartridge, an all-fluoropolymer membrane cartridge. Contact your local Pall representative or distributor for specific information on these products.

2 Because so many factors (e.g. elevated temperatures) can affect the
chemical resistance of a given product, you should pre-test under your
own operating conditions observing applicable safety practices such as
those given in the Material Safety Data Sheet for each chemical. Pall
Corporation can provide specific compatibility guidance, testing and data
upon request.
Performance

Liquid Retention Ratings (μm) (by ASTM F-795 Test)

 
Single Pass Multi-Pass
0.5 0.2
1 0.5
3 1
10 3
25 10
 

Typical Flow vs. Differential Pressure for Application Sizing



Unit conversion: 1 bar = 100 kPa

Flow rate is for a 25.4 cm (10 in) cartridge. For liquids other than water, multiply differential pressure by fluid viscosity (cP).
Type
Cartridges and Elements
Use
Filtration
Ordering Information
Pall Part Number = T [1] [2] [3] Y – [4]

Table 1

 
Code Filter grades (μm)
0.5 0.5
001 1
003 3
010 10
025 25
 

Table 2

 
Code Diameter (cm/in.) nominal
A 6.35/2.5
BB 7.14 /2.81
 

Table 3

 
Code Cartridge lengths (cm/in) nominal
10 25.4/10
204 50.8/20
304 76.2/30
 

Table 4

 
Code End configurations
Blank DOE industrial
M3 SOE flat closed end, external 222 O-ring (retrofits other manufacturers’ Code 0)3 (“BB” diameter) – only
 
3 For details, contact Pall Corporation.
4 If selecting Code ‘A’ (Table 2) and Code ‘20’ or ‘30’ in Table 3, add a ‘W’ in front of the Table 3 code. For example, ‘AW20’ or ‘AW30’ for the correct part number.
Application
Chem Intermediate Product (Other), Chemicals Raw Material / Gas/Air, Poly Cmdty Intermediate (Fluids), Poly Cmdty Raw Material (Fluids), Poly Engrd & Spcl Intermediate (Fluids), Poly Engrd & Spcl Raw Material (Fluids), Chem Final Product (Liquid)