Documents
Datasheets
Download:Description
High Capacity Pleated
Polypropylene Filter Elements
- New, larger cartridge geometry
- High flow capacity
- Poly-Fine® II proprietary media for highly consistent filtration
- Inside-out flow traps contaminant inside the element
- Available to fit most Size 1 and Size 2 bag housings with no hardware changes
- Available in 101.6 cm (40 in) for use in unique 101.6 cm (40 in) Marksman housings
- Unique sealing device adjusts to fit in most bag filter housings
- High surface area for long service life
- All polypropylene construction
- Wide chemical compatibility
- Short length option to accommodate shorter baskets
Specifications
Filter Grades
- 1, 3, 5, 10, 20, 40, 70, 90, 150 micron (μm)
Maximum Operating Differential Pressure
- To 5.2 bard @ 20 °C (75 psid @ 68 °F)
- To 2.4 bard @ 74 °C (35 psid @ 165 °F)
Recommended Change-out Differential Pressure1
- 2.4 bard @ up to 54 °C (35 psid @ up to 130 °F)
Food and Water Contact Use
- Please contact Pall Corporation to verify that the product conforms to your national legislation and/or regional regulatory requirements for water and food contact use.
Purity
- Cartridges do not use surfactants, binders, and adhesives.
Sanitization
- contact Pall Corporation for assistance.
Materials of Construction
- Filter media: Polypropylene
- Hardware: Polypropylene
- Support material: Polypropylene
- Gaskets: EPDM, fluorocarbon elastomer, nitrile
- Sealing: Thermal bond
Dimensions (Nominal)
- Outside flange diameter: Three diameters are available. contact Pall for information on sizes.
- Outside filter diameter: 15.2 cm (6 in.)
- Lengths:
Size 1 - Standard, Short
Size 2 - Standard, Short, Extra Short
Size 4 - 101.6 cm (40 in)
Particle Removal Ratings2 (μm)
Cartridge Designation | 90% Efficiency | >99.9% Efficiency |
PFTM 1 | 1 | - |
PFTM 3 | 2 | - |
PFTM 5 | - | 5 |
PFTM 10 | - | 9 |
PFTM 20 | - | 15 |
PFTM 40 | 20 | - |
PFTM 70 | - | 70 |
PFTM 90 | 57 | - |
PFTM 150 | - | 145 |
Typical Flow
mbard/lpm (psid/gpm) Water @ 20°C (68°F) | |||||
Filter Grade | Size 1 | Size 2 | 40 in | Size 1 (short) | Size 2 (short) |
1 | 0.838 (0.046) |
0.364 (0.020) |
0.273 (0.015) |
0.765 (0.042) |
0.328 (0.018) |
3 | 0.346 (0.019) |
0.164 (0.008) |
0.109 (0.006) |
0.310 (0.017) |
0.128 (0.007) |
5 | 0.109 (0.006) |
0.054 (0.003) |
0.018 (0.001) |
0.109 (0.006) |
0.054 (0.003) |
10 | 0.054 (0.003) |
0.018 (0.001) |
0.018 (0.001) |
0.054 (0.003) |
0.018 (0.001) |
20 | 0.036 (0.002) |
0.018 (0.001) |
0.018 (0.001) |
0.036 (0.002) |
0.018 (0.001) |
40 | 0.018 (0.001) |
0.018 (0.001) |
0.018 (0.001) |
0.036 (0.002) |
0.018 (0.001) |
70 | 0.018 (0.001) |
0.018 (0.001) |
0.018 (0.001) |
0.018 (0.001) |
0.018 (0.001) |
90 | 0.018 (0.001) |
0.018 (0.001) |
0.018 (0.001) |
0.018 (0.001) |
0.018 (0.001) |
150 | 0.018 (0.001) |
0.018 (0.001) |
0.018 (0.001) |
0.018 (0.001) |
0.018 (0.001) |
1Provided that the maximum differential pressure is not exceeded based on temperature limits defined above.
2Marksman PFT series filter cartridge retention ratings are based on Pall’s Dynamic Efficiency test protocol. This single pass, destructive challenge test is based on ASTM F-795 test procedures for determining the performance of a filter medium. Fine test dust is used as the test contaminant for filters in the 1 to 20 micron range. Coarse test dust is used for micron ratings above 20 micron. Additional information can be obtained by contacting Pall Corporation. NOTE: PFTM grade designations for 1, 3, 40, and 90 based on Beta 10 values, and all other grade designations are based on Beta 1000 values.
Type
Large Format Filters
Ordering Information
This information is a guide to the part number structure and possible options. For availability of specific options and housing details, please contact Pall.
Example Part Number: PFTM S 3 - 1 U V - PF B ( See bold references in tables below)
3Size 2 (only)
Part Number: PFTM < Length Code from Table 1 > < Length Code from Table 2 > - < Cartridge Code from Table 3 > U < Gasket Code from Table 4 > - < Configuration Code from Table 5 > < Flange/Gasket Code from Table 6 >
Table 1 - Short Length Option
Code | Short Length Option |
Blank | Standard |
S | Short |
XS | Extra short 3, 4 |
Table 2 - Filter Grades (µm)
Code | Filter Grades (μm) |
1 | 1 |
3 | 3 |
5 | 5 |
10 | 10 |
20 | 20 |
40 | 40 |
70 | 70 |
90 | 90 |
150 | 150 |
Table 3 - Cartridge Lengths Nominal
Code | Cartridge Lengths Nominal |
1 | Size 1 bag |
2 | Size 2 bag |
4 | 101.6 cm |
Table 4 - Gasket Materials
Code | Gasket Materials |
Blank | For NF version |
N | Nitrile |
E | EPDM (peroxide cured) |
V | Fluorocarbon elastomer |
Table 5 - End Configuration
Code | End Configurations |
PF | Plastic self-adjusting flange |
SF | Stainless steel self-adjusting flange (required for temperatures >43°C/110°F) |
NF | No flange (for use with reusable SS flange) |
Table 6 - Flange/Gasket styles5
Code | Flange/Gasket Styles5 |
A6 | Rosedale7, Strainrite, Krystil Klear8, Pall |
B | GAF9, FSI10 side entry |
C | FSI over the top, Hayward11 over the top |
3Size 2 (only)
4Select “XS” for Extra Short, “2” for Size 2 bag, and add “68” to the end of the part number (e.g., PFTMXS1-2UN-PFC 68).
5For housings not listed or other than original equipment baskets, consult your Pall sales representative for proper flange/gasket style.
6Requires “A” flange if using any of the Marksman 101.6 cm (40 in) products in the 101.6 cm (40 in) Pall Marksman housing.
7Rosedale is a registered trademark of Rosedale Products, Inc.
8Krystil Klear is a registered trademark of Pentair Water Filtration.
9GAF is a registered trademark of GAF Corporation.
10FSI is a registered trademark of Filter Specialists, Inc.
11Hayward is a registered trademark of Hayward Industrial Products, Inc.
Reviews
We appreciate your review of this product. Please login to your account to leave a review.