MICROsorp OC filter cartridges are regenerable prefilters designed with a tight pore structure to maximize the service life of downstream membrane filters in bottled water and wine pre-filtration applications.
The MICROsorp OC has a pleated filter pack comprising a resin-bonded liquid crystal fiber filter medium with cellulose substrate. The dense fiber structure provides excellent protection of downstream membrane filters while the robust media enables repeated regenerations to maximize service life.
The single open ended (SOE) configuration can be hot water sanitized or steam sterilized in situ for hygienic and flexible operation.
|Fixed pore structure||
- Cartridges produced in a controlled environment
- Manufactured according to ISO 9001:2015 certified Quality Management System
Food Contact Compliance
Please refer to the Pall website www.pall.com/foodandbev for a Declaration of Compliance to specific National Legislation and/or Regional Regulatory requirements for food contact use.
Materials of Construction
|Filter Medium||Resin bonded liquid crystal fibers on a cellulose substrate|
|Support / Drainage, Side Seal Clip, Core, End Cap and Fin End, Cage||Polypropylene|
|Adaptor||Polypropylene with internal stainless steel reinforcing ring|
|O-ring seal||Silicone elastomer (S) or Ethylene Propylene Rubber (E)|
Technical InformationLiquid Removal Rating1
Liquid removal rating: 0.8 micron @ 99.98% Efficiency (β5000)
Operating Characteristics in Compatible Fluids2
|Maximum Differential Pressure||Operating Temperature|
|5.5 bard (80 psid) (forward)||50 °C (122 °F)|
|4.1 bard (60 psid) (forward)||80 °C (176 °F)|
|500 mbard (7 psid) (reverse)||20 °C (68 °F)|
Sterilization and Sanitization
|Steam||121 °C (250 °F)||25 hours|
|Hot Water||90 °C (194 °F)||50 hours|
|Peroxyacetic acid based sanitizer (300 ppm total peroxides)||20 °C (68 °F)||50 hours|
Typical Flow Rates4
This information is a guide to the part number structure and possible options. For availability of specific options and housing details, please contact Pall.
Cartridge Part Number: 469 A080 W [Table1] [Table2] [Table3] P
Table 1: Adaptor
|02||SOE – single open end with flat closed end, 2 locking tabs and external 226 o-rings|
|03||SOE – single open end with flat closed end and external 222 O-rings|
|07||SOE – single open end with fin end, 2 locking tabs and external 226 O-rings|
|28 or 41||SOE – single open end with fin end, 3 locking tabs and external 222 O-rings|
Table 2: Nominal Length
|1||254 mm (10")|
|2||508 mm (20")|
|3||762 mm (30")|
|4||1016 mm (40")|
Table 3: O-Ring Seal Material
|E||Ethylene Propylene Rubber|
1The MICROsorp OC Filter Cartridge liquid retention rating is based on modified OSU-F2 test.
2 Compatible fluids are defined as those which do not swell, soften or attack any of the filter components.
3 Measured under laboratory test conditions. The actual cumulative time depends on the process conditions. Pall recommends the use of Code 7 adaptors to ensure filter sealing after cooling. Cartridges should be cooled to system operating temperature prior to use. Contact Pall for recommended procedures.
4 Typical initial clean media ΔP 254 mm (10") cartridge for water at 20 °C (68 °F); viscosity 1 centipoise. For 508 mm, 762 mm and 1016 mm configurations divide the differential pressure by 2, 3, and 4 respectively.