SUPRA Filtration For Cannabis Oil FiltrationSUPRA Cannabis System E Series are simple, plug and play skids designed to revolutionize depth filtration applications in the cannabis industry. The systems are designed incorporating Pall’s unique SUPRApak™ and SUPRADisc™ M filter modules and cartridge filters providing a cost-effective alternative to classical sheet filtration and decolorization.
SUPRA Cannabis System E Series filtration units provide a closed system approach to high capacity depth filtration, maximizing product protection and minimizing product losses. Lower cost of ownership is achieved due to higher throughput, yield improvement, and reduced handling, cleaning, maintenance and downtime costs, when compared to sheet filtration.
SUPRA Cannabis System E Series technology is ideal for use in cannabis applications for wax and color removal for flow rates (or volumes) between X and Y. All components and critical measurement devices are assembled on a mobile, easy to install and operate skid (or something like that).
The E series units are set up to include 3 stages of filtration. For clarification and wax removal , SUPRA Cannabis System E Series units hold 1 or 2 SUPRApak M modules, each representing up to approximately 2.7 m2 (29.1 ft2) of filtration area or 1 or 2 SUPRAdisc II 12 inch modules, representing up to 1.8 m2 of area enabling compact and low hold-up volume system design. After the clarification step, SUPRAdisc AKS Modules are positioned for color removal. The third and final step is a guard filtration step using cartridge filters.
|Closed filtration system||
|Compact design with high filtration area||
|Drainable, low hold-up volume assembly||
|High quality internal surface finish, sanitary and crevice-free design||
|Simple, quick installation and servicing||
|Filter module lifting device available on request||
|European ATEX Directive, Group 2, Category III documentation (Zones 1/21 and 2/22)||
|Minimum/Maximum Design Pressure1, 2||Liquids: -1 to 6 barg(-14.5 to 87 psig)|
|Minimum/Maximum Operationg Temperature1||40 to 130 °C (-40 to 266 °F)|
|Materials of Construction||Wetted parts 1.4404 (AISI 316L stainless steel)|
|Sealing Materials3||Silicon elastomer|
|Internal Surface Finish||<e; 0.8 micrometers Ra (<e; 32 Ra microinches), electropolished|
|Internal Welds||Dressed and blended to provide uniform ripple- and crevice-free surface to <e; 0.8 micrometers Ra (<e; 32 Ra microinches), electropolishe|
|Connections Inlet/Outlet||1 inch ISO 2852 clamp coupling|
|Filtrate Vent||DN6 (8 mm / 0.31 inch OD) hose tail|
|Filter Module Compatibility4||SUPRApak M Series Modules; SUPRAdisc II Modules; Code 7 Pall Cartridges; SUPRAdiscAKS 4 Modules|
|1 Maximum design pressure and temperature ratings are vessel ratings only. Safe operation will also depend on filter module and housing gasket use. Silicone assembly seals restrict continuous operating temperature to -40 to 130 ºC (266 ºF). For details on module temperature limitations, please refer to SUPRApak module literature and Pall code 7 ca.
2 Design satisfies EC Pressure Equipment Directive (PED Assessment) (Fluid Group 2, Category III, Module H). Pressure rating is suitable for non-hazardous liquids or gases. The PED category and fluid group classification indicates suitability of housing use on distilled spirits less than 70% by weight absolute alcohol. For such applications, the maximum allowable temperature must be below the flash point. For 70% by weight absolute alcohol the flashpoint is 21 °C (69.8 °F).
3 Please contact Pall to ensure the products meet specific National Legislation and/or Regional Regulatory requirements for food contact use.
4 Refer to Pall Food and Beverage SUPRApak module literature for additional guidelines on use.
|Nominal Dimenstions in mm (inches) - For specific dimensions, Please contact Pall5|
|SUPRA Cannabis System E121||CSKDWZ121013||1835 (72.25)||1471 (57.875)||1093 (43)||975 (38.375)||1300 (51.125)|
|SUPRA Cannabis System E122||SCSKDWZ122033||1730 (68.125)||1491 (58.75)||1093 (43)||975 (38.375)||1300 (51.125)|
|5 Pall Corporation reserves the right to make dimensional modifications at any time, maintaining the same fit, form, and function. Please request a general arrangement drawing if exact dimensions are required|
|Volumes and Weight|
|E121||E122||Code 7 3 Round 30"||Code 7 5 Round 30"||WSF 12-01||WSF12-02|
|Volume L (US gal)||-||-||6.3 (1.7)||20 (5.3)||32 (8.5)||53 (14)|
|Weight kg (lb)||400 (882)||400 (882)||6 (13.2)||23.5 (51.8)||45 (99.2)||50 (110.2)|
- Certificate of Conformity to Quality Standards
- Final Inspection Certificate
- Installation/Operating Manual (IOM)
This is a guide to the part numbering structure and possible options only. For availability of specific options, please contact Pall.
|PN||Housing 1||Housing 2||Housing 3|
|CSKDWZ121013||WSFC 12-01||WSFC 12-01||Code 7 Housing – 1 Round 30"|
|SCSKDWZ122033||WSFC 12-02||WSFC 12-02||Code 7 Housing – 3 Round 30"|
|General Description||Part No.||Housing Used|
|SUPRAdisc II Module||7007872||WSFC Housing|
|SUPRAdisc II Module||7007866||WSFC Housing|
|SUPRApak PLUS Module||5303071/M||WSFC Housing|
|SUPRApak PLUS Module||5303072/M||WSFC Housing|
|SUPRAdisc II AKS 4 Module||7007996||WSFC Housing|
|Nexis® T Filter||NXT1030UM7WS480||Code 7 Housing|
|Nexis T Filter||NXT2030UM7WS480||Code 7 Housing|
|Profile® Star||AB3A0107WH4||Code 7 Housing|
|PolyFine® II||PFT 0.8-30UE-M7W 480||Code 7 Housing|
|PolyFine II||PFT 0.25-30US-M7W 480||Code 7 Housing|