Order Products
Gasket / O-Ring Material
FEP encapsulated fluorocarbon elastomer (O-rings)
Nexis® T Filter Cartridges, Removal Rating 150 μm, Polypropylene, Length 27.25 inches
Product ID: NXT1502725UM18F
Unit of Measure
1/EA
1/EA
Min Order Qty
1
1
Micron
150 micron
Nexis, NXT, 10 μm, 25.4 cm (10 in), SOE flat closed end, external 222 O-rings (retrofits other manufacturers’ Code 0), FEP encapsulated fluorocarbon elastomer (O-rings)
Product ID: NXT1010UM3F
Unit of Measure
1/EA
1/EA
Min Order Qty
1
1
Micron
10 micron
Nexis, NXT, 3 μm, 25.4 cm (10 in), SOE flat closed end, external 222 O-rings (retrofits other manufacturers’ Code 0), FEP encapsulated fluorocarbon elastomer (O-rings)
Product ID: NXT310UM3F
Unit of Measure
1/EA
1/EA
Min Order Qty
1
1
Micron
3 micron
Nexis® T Filter Cartridges, Removal Rating 100 μm, Polypropylene, Length 27.25 inches
Product ID: NXT1002725UM18F
Unit of Measure
1/EA
1/EA
Min Order Qty
1
1
Micron
100 micron
Nexis® T Filter Cartridges, Removal Rating 25 μm, Polypropylene, Length 16.25 inches
Product ID: NXT251625UM3F
Unit of Measure
1/EA
1/EA
Min Order Qty
1
1
Micron
25 micron
Nexis® T Filter Cartridges, Removal Rating 75 μm, Polypropylene, Length 16.25 inches
Product ID: NXT751625UM3F
Unit of Measure
1/EA
1/EA
Min Order Qty
1
1
Micron
75 micron
Nexis® T Filter Cartridges, Removal Rating 10 μm, Polypropylene, Length 16.25 inches
Product ID: NXT101625UM3F
Unit of Measure
1/EA
1/EA
Min Order Qty
1
1
Micron
10 micron
Nexis® T Filter Cartridges, Removal Rating 5 μm, Polypropylene, Length 16.25 inches
Product ID: NXT51625UM3F
Unit of Measure
1/EA
1/EA
Min Order Qty
1
1
Micron
5 micron
Nexis® T Filter Cartridges, Removal Rating 0.5 μm, Polypropylene, Length 30 inches, FEP encapsulated Fluorocarbon Elastomer Orings
Product ID: NXT0530UM26F
Unit of Measure
1/EA
1/EA
Min Order Qty
1
1
Micron
0.5 micron
Nexis, NXT, 1 μm, 25.4 cm (10 in), SOE flat closed end, external 222 O-rings (retrofits other manufacturers’ Code 0), FEP encapsulated fluorocarbon elastomer (O-rings)
Product ID: NXT110UM3F
Unit of Measure
30/EA
30/EA
Min Order Qty
30
30
Micron
1 micron
Nexis® T Filter Cartridges, Removal Rating 50 μm, Polypropylene, Length 27.25 inches
Product ID: NXT502725UM18F
Unit of Measure
1/EA
1/EA
Min Order Qty
1
1
Micron
50 micron
Nexis® T Filter Cartridges, Removal Rating 20 μm, Polypropylene, Length 10 inches, FEP encapsulated Fluorocarbon Elastomer Orings, SOE flat closed end external 222 O-ring
Product ID: NXT2010UM18F
Unit of Measure
1/EA
1/EA
Min Order Qty
1
1
Micron
20 micron
Documents
Datasheets
Download:Description
- Proprietary CoLD Melt™ fiber technology
- Continuous gradient pore structure media provides both prefiltration and final filtration
- Proprietary center core for greater mechanical strength and chemical resistance (0.5 - 10 !m)
- Resists contaminant unloading even at high differential pressures
- Computer controlled CoLD Melt manufacturing process increases product consistency
- Polypropylene media construction
- Thermally bonded structure - not employing adhesives
- Plastic and metal spring assembly end configurations are available
For detailed information about this product, please refer to the data sheet. (To download this data sheet, select Download PDF from the menu above.)
Products in this datasheet may be covered by one or more patents, including EP 830,191; US 5,591,335; US 5,653,833; US 5,681,469; US 5,690,782; US 5,730,820; US 5,733,581; US 5,741,395; US 5,783,011.
Specifications
Materials of construction
- Filter media: Polypropylene
- Hardware: Polypropylene
- Gaskets/O-rings: Silicone elastomer, EPDM, nitrile, fluor ocarbon elastomer, FEP, thermoplastic elastomer (DOE only), FEP encapsulated silicone elastomer, FEP encapsulated fluorocarbon elastomer
Dimensions (nominal)
- Outside diameter: 6.4 cm (2.5 in.)
- Lengths: 10.2 cm (4 in.), 12.7 cm (5 in.), 24.8 cm (9.75 in.), 25.1 cm (9.875 in.), 25.4 cm (10 in.), 49.5 cm (19.5 in.), 50.8 cm (20 in.), 74.3 cm (29.25 in.), 76.2 cm (30 in.), 99.1 cm (39 in.), 100.3 cm (39.5 in.), 102 cm (40 in.)
Performance
Filter grades1
0.5, 1, 3, 5, 7, 10, 15, 20, 25, 30, 40, 50, 75, 100, 120, 150, 200 µmMaximum differential pressure
- 0.5-10 μm:
- 1.03 bard @ 82 °C (15 psid @ 180 °F)
- 1.72 bard @ 66 °C (25 psid @ 150 °F)
- 4.14 bard @ 30 °C (60 psid @ 86 °F)
- 15-120 μm:
- 1 .72 bard @ 60 °C (25 psid @ 140 °F)
- 3.45 bard @ ambient (50 psid @ ambient)
Recommended change-out differential pressure2
2.4 bar d (35 psid)Food and water contact use
Please contact Pall Corporation to verify that the product conforms to your national legislation and/or regional regulatory requirements for water and food contact use.Rinse-up
Rinse-up to 18 Megohm-cm with a minimum of throughput.Autoclaving
Single-open-end Nexis T series filter cartridges can be autoclaved for 30 minutes at 121 °C (250 °F) under no end load conditions. However , filter cartridges should be allowed to cool to normal system operating temperatures prior to use.Steam sterilization
Not recommended.Typical Flow vs. Differential Pressure for Application Sizing3
1 >90% retention rating by ASTM F-795 test. Nexis T series filter cartridge retention ratings are based on Pall's Dynamic Efficiency test protocol. This single pass, destructive challenge test is based on ASTM F-795 test procedures for determining the performance of a filter medium. Fine test dust is used as the test contaminant for filters in the 0.5 to 20 micron range. Coarse test dust is used for micron ratings above 20 micron. Additional information can be obtained by contacting Pall Corporation.
2 Provided that the maximum differential pressure is not exceeded based on temperature limits defined above.
3 Due to the very low flow resistance of the media in the more open grades, pressure drop is primarily related to turbulent loss through the center core. Flow rate is for a 25.4 cm (10 in.) cartridge. For liquids other than water, multiply differential pressure by fluid viscosity (cP).
Type
Filter Cartridges
Ordering Information
Pall Part Number = NXT [1] [2] U - [3] [4]
Table 1
|
Table 2
|
Table 3
Code | End configurations |
Blank | DOE industrial (no end caps) |
1X | DOE, 2.54 cm (1 in.) extended core |
M3 | SOE flat closed end, external 222 O-rings (retrofits other manufacturers’ Code 0)4 |
M3H | SOE large diameter closed end, external 222 O-rings |
M4 | SOE fin end, external 222 O-rings with locking tabs (silicone and EPDM O-rings only) |
M5 | DOE, internal 120 O-rings (retro fits 213 O-ring style)4 |
M6 | SOE flat closed end, external 226 O-rings (retrofits other manufacturers’ Code 6)4 |
M7 | SOE fin end, external 226 O-rings (retrofits other manufacturers’ Code 7)4 |
M8 | SOE fin end, external 222 O-rings (retro fits other manufacturers’ Code 5)4 |
M10 | DOE, internal O-rings (fits other manufacturers’ housings)4 |
M11 | SOE flat closed end, internal 120 O-ring (retrofits other manufacturers’ X style)4 |
M18 | SOE flat closed end, external 222 O-ring |
M20 | SOE with internal O-rings (same as M10), closed end with deep recess |
DOE | DOE with elastomer gasket seals and end caps |
H21 | DOE, Santoprene gasket seal |
XK | SOE plastic spring assembly, saw cut end |
SI | SOE metal spring / polypropylene cap, saw cut end |
Table 4
Code | Gasket/O-ring materials |
S | Silicone |
N | Nitrile |
E | EPDM |
V | Fluorocarbon elastomer |
T | Expanded PTFE (gaskets) - DOE option FEP encapsulated silicone (O-rings) - SOE option |
F | FEP encapsulated fluor ocarbon elastomer (O-rings) |
Y | Santoprene |
4 For details, contact Pall Corporation.
Reviews
We appreciate your review of this product. Please login to your account to leave a review.