Claris® Series Filter Cartridges
* Required
Need Help?
Description
High Consistency Polypropylene
High Consistency Polypropylene
Melt Blown Cartridge
- Graded pore structure enhances dirt-holding capacity
- E-core, an Extruded Fibrous Core, provides excellent strength
- Unique proprietary process
- Easy and safe cartridge incineration and disposal
- All polypropylene construction
- No surfactants, binders, or adhesives
- NSF certified
- Plastic and metal spring assembly end configurations are available
Specifications
1 Provided that the maximum differential pressure is not exceeded based on temperature limits defined above.
Performance Specifications
Filter grades
- 1, 3, 5, 10, 20, 30, 50, 75 micron (μm)
Maximum differential pressure
- 3.45 bard (50 psid) @ 20 °C (68 °F)
- 1.72 bard (25 psid) @ 60 °C (140 °F)
Recommended change-out differential pressure1
- 2.4 bard (35 psid)
Food and Water Contact Use
- Please contact Pall Corporation to verify that the product conforms to your national legislation and/or regional regulatory requirements for water and food contact use.
Purity
- Cartridges do not use surfactants, anti-static agents, binders, and adhesives.
Product Specifications
Materials of construction
| Filter media: | Polypropylene |
| End caps2: | Polypropylene |
| Extended core2: | Stainless steel |
| Extruded core: | Polypropylene |
| Gaskets/O-rings2: | Silicone elastomer, nitrile, fluorocarbon elastomer, EPDM, Santoprene3 |
Dimensions (nominal)
| Outside diameter: | 6.4 cm (2.5 in.) |
| Inside diameter: | 2.7 cm (1.07 in.) |
| Lengths: | 24.8 cm (9.75 in.), 25.1 cm (9.875 in.), 25.4 cm (10 in.), 49.5 cm (19.5 in.), 50.2 cm (19.75 in.), 50.8 cm (20 in.), 74.3 cm (29.25 in.), 74.9 cm (29.5 in.), 75.6 cm (29.75 in.), 76.2 cm (30 in.), 99.1 cm (39 in.), 102 cm (40 in.), 127 cm (50 in.) |
1 Provided that the maximum differential pressure is not exceeded based on temperature limits defined above.
2 These components are not NSF certified.
3 Trademark of Exxon Mobil Corporation.
Performance
Unit conversion: 1 bar = 100 kPa
Typical Flow vs. Differential Pressure for Application Sizing
Unit conversion: 1 bar = 100 kPa
Flow rate is for a 25.4 cm (10 in) cartridge. For liquids other than water, multiply differential pressure by fluid viscosity (cP).
Type
Filter Cartridges
Ordering Information
Pall Part Number = CLR - [1] - [2] [3] [4]
4 Based on typical application usage.
Table 1
| Code | Filter grades (μm)4 |
| 1 | 1 |
| 3 | 3 |
| 5 | 5 |
| 10 | 10 |
| 20 | 20 |
| 30 | 30 |
| 50 | 50 |
| 75 | 75 |
Table 2
| Code | Cartridge lengths (cm/in.) nominal |
| 9.75 | 24.8/9.75 |
| 9.875 | 25.1/9.875 |
| 10 | 25.4/10 |
| 19.5 | 49.5/19.5 |
| 19.75 | 50.2/19.75 |
| 20 | 50.8/20 |
| 29.25 | 74.3/29.25 |
| 29.5 | 74.9/29.5 |
| 29.75 | 75.6/29.75 |
| 30 | 76.2/30 |
| 39 | 99.1/39 |
| 40 | 102/40 |
| 50 | 127/50 |
Table 3
| Code | End configurations |
| Blank | DOE industrial (no end caps) |
| DOE | DOE with elastomer gasket seals & end caps |
| H21 | DOE, Santoprene gasket seal |
| 1X | DOE industrial, 2.54 cm (1 in) stainless steel extended core |
| M3 | SOE flat closed end, external 222 O-rings (retrofits other manufacturers' Code 0)5 |
| M6 | SOE flat closed end, external 226 O-rings (retrofits other manufacturers' Code 6)5 |
| M7 | SOE fin end, external 226 O-rings (retrofits other manufacturers' Code 7)5 |
| M8 | SOE fin end, external 222 O-rings (retrofits other manufacturers' Code 5)5 |
| M18 | SOE flat closed end, external 222 O-ring |
| XK | SOE plastic spring assembly, saw cut end |
| SI | SOE metal spring/polypropylene cap, saw cut end |
Table 4
| Code | Gasket/O-ring materials |
| S | Silicone |
| N | Nitrile |
| E | EPDM |
| V | Fluorocarbon elastomer |
4 Based on typical application usage.
5 For details, contact Pall Corporation.
Application
Injection Water
