Order Products
Narrow Your Results By
Results Below
356
Cant find what you are looking for?
Contact a Pall Representative
Contact a Pall Representative
Artikel-Nr.
PFT55UEM3
PFT55UEM3
Micron
5 µm
5 µm
Masseinheit
EA
EA
Min Bestellmenge
1
1
Micron
30 µm
30 µm
Masseinheit
EA
EA
Min Bestellmenge
1
1
Micron
30 µm
30 µm
Masseinheit
EA
EA
Min Bestellmenge
1
1
Micron
0.8 µm
0.8 µm
Masseinheit
EA
EA
Min Bestellmenge
1
1
Micron
0.8 µm
0.8 µm
Masseinheit
EA
EA
Min Bestellmenge
1
1
Micron
0.25 µm
0.25 µm
Masseinheit
EA
EA
Min Bestellmenge
1
1
Micron
10 µm
10 µm
Masseinheit
EA
EA
Min Bestellmenge
1
1
Artikel-Nr.
PFT025975UE
PFT025975UE
Micron
0.25 µm
0.25 µm
Masseinheit
EA
EA
Min Bestellmenge
1
1
Micron
2 µm
2 µm
Masseinheit
EA
EA
Min Bestellmenge
1
1
Micron
0.45 µm
0.45 µm
Masseinheit
EA
EA
Min Bestellmenge
1
1
Micron
0.8 µm
0.8 µm
Masseinheit
EA
EA
Min Bestellmenge
1
1
Micron
0.2 µm
0.2 µm
Masseinheit
EA
EA
Min Bestellmenge
1
1
Beschreibung
- Proprietary filter media produced by Pall for highly consistent performance
- High contaminant-holding capacity
- Wide chemical compatibility
- Rigid polypropylene outer cage protects filter
- All polypropylene one piece construction (except 0.2 micron)
- Asymmetric polysulfone media used in 0.2 μm grade
- Fast rinse-up to 18 Megohm-cm
Spezifikationenn
Performance Specifications
Filter Grades:
0.2, 0.25, 0.45, 0.8, 2, 3, 5, 10, 30, 50, 100 μmRecommended change-out differential pressure1
2.4 bard (35 psid)Maximum forward differential pressure
4.8 bard (70 psid) @ 20°C (68°F)2.8 bard (40 psid) @ 65°C (150°F)
Food and water contact use
Please contact Pall Corporation to verify that the product conforms to your national legislation and/or regional regulatory requirements for water and food contact use.Cartridge rinse-up
Rinse-up to 18 Megohm-cm with a minimum of throughput.Purity
Cartridges are free of resins, binders, and adhesives.Sterilization:
Multiple autoclaving for 30 minutes at 121°C (250°F) under no end load conditions. In -line steam sterilization is not recommended. May be in-line sanitized with hot water at 82°C (180°F) for 1 hour.Product Specifications
Materials of construction
Filter Media: | |
PFT 0.2: | Highly asymmetric polysulfone |
All other grades: | Polypropylene |
Hardware: | Polypropylene |
Sealing: | Thermal bond |
Support material: | Polypropylene |
Gaskets/O-rings: | Silicone elastomer, nitrile, EPDM fluorocarbon elastomer, white nitrile, white silicone, expanded PTFE, FEP encapsulated silicone, high purity fluorocarbon elastomer, FEP encapsulated fluorocarbon elastomer, Kalrez2, white neoprene |
Dimensions (nominal):
Outside Diameter: | 6.6 cm (2.6 in) |
Lengths: | 10.2 cm (4 in), 24.8 cm (9.75 in), 25.4 cm (10 in), 49.5 cm (19.5 in), 50.8 cm (20 in), 74.3 cm (29.25 in), 76.2 cm (30 in), 99.1 cm (39 in), 102 cm (40 in) |
1 Provided that the maximum differential pressure is not exceeded based on temperature limits defined above.
2 Registered trademark of DuPont Dow.
Leistung
Particle Retention (µm)
Cartridge Designation | Liquid Service (by ASTM F-795 Test) | Gas Service | |
90% Efficiency | >99.9% Efficiency | Removal Efficiency By DOP Test | |
PFT 0.2 | 0.2 | 0.5 | 99.99% |
PFT 0.25 | 0.25 | 1.0 | 99.97% |
PFT 0.45 | 0.45 | 1.2 | 99.93% |
PFT 0.8 | 0.8 | 2.5 | 99.90% |
PFT 2.0 | 2 | 5 | - |
PFT 3.0 | 3 | 7 | - |
PFT 5.0 | 5 | 12 | - |
PFT 10.0 | 10 | 15 | - |
PFT 30.0 | 30 | 40 | - |
PFT 50.0 | 50 | 65 | - |
PFT 100.0 | 85 | 100 | - |
Typical Flow vs. Differential Pressure for Application Sizing
Flow rate is for a 25.4 cm (10 in) cartridge. For liquids other than water, multiply differential pressure by fluid viscosity (cP).
Unit conversion: 1 bar = 100 kPa
Typ
Filter Cartridges
Bestellinformation
Pall Part Number = PFT [1] - [2]U[3] - [4][5][6] - [7]
Table 1
Code | Filter grades (μm) |
0.2 | 0.2 |
0.25 | 0.25 |
0.45 | 0.45 |
0.8 | 0.8 |
2 | 2 |
3 | 3 |
5 | 5 |
10 | 10 |
30 | 30 |
50 | 50 |
100 | 100 |
Table 2
Code | Cartridge lengths (cm/ in) nominal |
4 | 10.2/4 |
9.75 | 24.8/9.75 |
10 | 25.4/10 |
19.5 | 49.5/19.5 |
20 | 50.8/20 |
29.25 | 74.3/29.25 |
30 | 76.2/30 |
39 | 99.1/39 |
40 | 101.6/40 |
Table 3
Code | Gasket/O-ring materials |
S | Silicone (standard O-rings) |
N | Nitrile (standard gaskets) |
M | White silicone |
W | White nitrile (gaskets) |
V | Fluorocarbon elastomer |
E | EPDM |
T | FEP encapsulated silicone (O-rings) |
T | Expanded PTFE (gaskets) |
X | No O-ring required (M2 style only) |
F | FEP encapsulated fluorocarbon elastomer (O-rings) |
K | Kalrez (222 O-rings) |
Q | High purity fluorocarbon elastomer (222 O-rings) |
Z | White neoprene (gaskets) |
Table 4
Code | End configurationss |
Blank | DOE industrial |
1X | DOE industrial, 2.54 cm (1 in) extended core |
M2 | SOE flat closed end, fits housings with 020 O-ring post |
M3 | SOE flat closed end, external 222 O-rings (retrofits other manufacturers’ Code 0)3 |
M3H | SOE large diameter closed end, external 222 O-rings |
M4 | SOE fin end, external 222 O-rings with locking tabs |
M5 | DOE, internal 120 O-rings (retrofits 213 O-ring style) 3 |
M6 | SOE flat closed end, external 226 O-rings (retrofits other manufacturers’ Code 6)3 |
M7 | SOE fin end, external 226 O-rings (retrofits other manufacturers’ Code 7)3 |
M8 | SOE fin end, external 222 O-rings (retrofits other manufacturers’ Code 5)3 |
M10 | DOE, internal O-rings (fits other manufacturers’ housings)3 |
M11 | SOE flat closed end, internal 120 O-ring (retrofits other manufacturers’ X style) 3 |
M18 | SOE flat closed end, external 222 O-ring |
M20 | SOE, internal O-ring (same as M10), closed end with deep recess |
M22 | SOE fin end, external 225 O-ring |
Table 5
Code | Bubble test option |
Blank | No bubble test |
B | 100% bubble best |
Table 6
Code | Pre-rinse option |
Blank | No pre-rinse |
414 | 100% pre-rinse |
Table 7
Code | Packaging |
Blank | Standard packaging |
-BLK | Bulk packaging |
3 For details, contact Pall Corporation.
Rezensionen
Earn 10% off* your next order online by leaving a review of this product. Please login to your account to leave a review. We appreciate and value your feedback.
*Subject to Terms and Conditions.