Spiral Wound Absolute Rated Depth Filter Cartridge
- Innovative depth filter cartridge technology
- All-polypropylene components
- Absolute rated at >99.9% efficiency with retention ratings from 0.5 to 70 microns
- Proprietary filter media produced directly by Pall for highly consistent, reproducible performance
- Spiral wound filter cartridge free of surfactants, binders and adhesives
- Graded pore structure provides pre and final filtration in one cartridge
- Resists contaminant unloading even at high differential pressures
0.5, 1, 3, 5, 10, 20, 40, 70 μm
Maximum differential pressure
1.0 bard @ 82°C (15 psid @ 180°F)
5.2 bard @ 20°C (75 psid @ 68°F)
NOTE: Heavy wall center core option is recommended for applications where the operating temperature exceeds 52°C (125°F).
Recommended change-out differential pressure2
2.4 bard (35 psid)
Food and water contact use
Please contact Pall Corporation to verify that the product conforms to your national legislation and/or regional regulatory requirements for water and food contact use.
Rinse-up to 18 Megohm-cm with a minimum of throughput.
Cartridges are free of surfactants, resins, binders, and adhesives.
Poly-Fine ARD Series filter cartridges are compatible with a broad array of fluids. Consult the factory for specific compatibility information.
Cartridge may be sanitized in place with common oxidizing agents. Consult the factory for compatibility information.
Materials of construction
|Gaskets/O-rings:||Silicone elastomer, EPDM, nitrile, fluorocarbon elastomer, expanded PTFE, FEP encapsulated silicone, white silicone, white nitrile, white neoprene, Santoprene3 (DOE only), FEP encapsulated fluorocarbon elastomer|
|Outside diameter:||6.6 cm (2.6 in)|
|Lengths:||10.2 cm (4 in), 24.8 cm (9.75 in), |
25.4 cm (10 in), 49.5 cm (19.5 in),
50.8 cm (20 in), 74.3 cm (29.25 in),
76.2 cm (30 in), 99.1 cm (39 in),
102 cm (40 in)
1- >99.9% retention rating by ASTM F-795 test.
2- Provided that the maximum differential pressure is not exceeded based on temperature limits defined above.
3- Registered trademark of Advanced Elastomer Systems.
Typical Flow vs. Differential Pressure for Application Sizing3
Unit conversion: 1 bar = 100 kPa
3- Flow rate is for a 25.4 cm (10 in) cartridge. For liquids other than water, multiply differential pressure by fluid viscosity (cP).
ARD ■ - ● ▐ ♦ - ▼ (e.g., ARD 10–10US–M3)
|Cartridge Lengths cm/in (nominal)|
|HW||Heavy wall polypropylene (except 0.5 μm)|
|T||Expanded PTFE (gaskets) |
FEP encapsulated silicone (O-rings)
|Z||White neoprene (gaskets)|
|F||FEP encapsulated fluorocarbon elastomer (O-rings)|
|1X||DOE, 2.54 cm (1 in) extended core|
|M3||SOE flat closed end, external 222 O-rings (retrofits other manufacturers’ Code 0)4|
|M3H||SOE large diameter closed end, external 222 O-rings|
|M4||SOE fin end, external 222 O-rings with locking tabs (silicone and EPDM O-rings only)|
|M5||DOE, internal 120 O-rings (retrofits 213 O-ring style)4|
|M6||SOE flat closed end, external 226 O-rings (retrofits other manufacturers’ Code 6)4|
|M7||SOE fin end, external 226 O-rings (retrofits other manufacturers’ Code 7)4|
|M8||SOE fin end, external 222 O-rings (retrofits other manufacturers’ Code 5)4|
|M10||DOE, internal O-rings (fits other manufacturers’ housings)4|
|M11||SOE flat closed end, internal 120 O-ring (retrofits other manufacturers’ X style)4|
|M18||SOE flat closed end, external 222 O-ring|
|M20||SOE with internal O-rings (same as M10), closed end with deep recess|
|DOE||DOE with elastomer gasket seals and end caps|
|H21||DOE, Santoprene gasket seal|
5- Leave blank if ordering H21 end configuration.