Claris® Series Filter Cartridges product photo Primary L

Claris® Series Filter Cartridges

High Consistency Polypropylene
Melt Blown Cartridge

  • Graded Pore Structure Enhances Dirt Holding Capacity
  • E-core, an Extruded Fibrous Core, Provides Excellent Strength
  • Unique Proprietary Process
  • Easy and Safe Cartridge Incineration and Disposal
  • All Polypropylene Construction
  • Free of Surfactants, Binders, and Adhesives
  • NSF Certified
  • Plastic and Metal Spring Assembly End Configurations Available
Products in this datasheet may be covered by one or more patents, including EP 1,165,205; US 6,342,283; US 6,662,842.


Contact Us
* Required

설명

High Consistency Polypropylene
Melt Blown Cartridge

  • Graded Pore Structure Enhances Dirt Holding Capacity
  • E-core, an Extruded Fibrous Core, Provides Excellent Strength
  • Unique Proprietary Process
  • Easy and Safe Cartridge Incineration and Disposal
  • All Polypropylene Construction
  • Free of Surfactants, Binders, and Adhesives
  • NSF Certified
  • Plastic and Metal Spring Assembly End Configurations Available
Products in this datasheet may be covered by one or more patents, including EP 1,165,205; US 6,342,283; US 6,662,842.

규격사양

Performance Specifications

Filter grades

  • 1, 3, 5, 10, 20, 30, 50, 75 micron (μm)

Maximum differential pressure

  • 3.45 bard (50 psid) @ 20 °C (68 °F)
  • 1.72 bard (25 psid) @ 60 °C (140 °F)

Recommended change-out differential pressure1

  • 2.4 bard (35 psid)

Food and Water Contact Use

  • Please contact Pall Corporation to verify that the product conforms to your national legislation and/or regional regulatory requirements for water and food contact use.

Purity

  • Cartridges do not use surfactants, anti-static agents, binders, and adhesives.

Product Specifications

Materials of construction

  • Filter media: Polypropylene
  • End caps2: Polypropylene
  • Extended core2: Stainless steel
  • Extruded core: Polypropylene
  • Gaskets/O-rings2:
    • Silicone elastomer
    • nitrile
    • fluorocarbon elastomer
    • EPDM
    • Santoprene3

Dimensions (nominal)

  • Outside diameter: 6.4 cm (2.5 in.)
  • Inside diameter: 2.7 cm (1.07 in.)
  • Lengths:
    • 24.8 cm (9.75 in.)
    • 25.1 cm (9.875 in.)
    • 25.4 cm (10 in.)
    • 49.5 cm (19.5 in.)
    • 50.2 cm (19.75 in.)
    • 50.8 cm (20 in.)
    • 74.3 cm (29.25 in.)
    • 74.9 cm (29.5 in.)
    • 75.6 cm (29.75 in.)
    • 76.2 cm (30 in.)
    • 99.1 cm (39 in.)
    • 102 cm (40 in.)
    • 127 cm (50 in.)
NSF Component

1Provided that the maximum differential pressure is not exceeded based on temperature limits defined above.
2 These components are not NSF certified.
3 Trademark of Exxon Mobil Corporation.

성능

Typical Flow vs. Differential Pressure for Application Sizing

Typical Flow vs. Differential Pressure for Application Sizing

Unit conversion: 1 bar = 100 kPa

Flow rate is for a 25.4 cm (10 in.) cartridge. For liquids other than water, multiply differential pressure by fluid viscosity (cP).

종류

Filter Cartridges

주문정보

This information is a guide to the part number structure and possible options. For availability of specific options and housing details, please contact Pall.

Example Part Number: CLR 10 20 DOE S ( See bold references in tables below)

Part Number:
CLR < Filter grade code from Table 1 > < Cartridge length code from Table 2 > < End configuration code from Table 3 > < Gasket/O-ring material code from Table 4 >

Table 1 - Filter grades

Code Filter grades (μm)4
1 1
3 3
5 5
10 10
20 20
30 30
50 50
75 75

Table 2 - Cartridge lengths

Code Cartridge lengths (cm/in.) nominal
9.75 24.8/9.75
9.875 25.1/9.875
10 25.4/10
19.5 49.5/19.5
19.75 50.2/19.75
20 50.8/20
29.25 74.3/29.25
29.5 74.9/29.5
29.75 75.6/29.75
30 76.2/30
39 99.1/39
40 102/40
50 127/50

Table 3 - End configurations

Code End configurations
Blank DOE industrial (no end caps)
DOE DOE with elastomer gasket seals & end caps
H21 DOE, Santoprene gasket seal
1X DOE industrial, 2.54 cm (1 in.) stainless steel extended core
M3 SOE flat closed end, external 222 O-rings (retrofits other manufacturers' Code 0)5
M6 SOE flat closed end, external 226 O-rings (retrofits other manufacturers' Code 6) 5
M7 SOE fin end, external 226 O-rings (retrofits other manufacturers' Code 7) 5
M8 SOE fin end, external 222 O-rings (retrofits other manufacturers' Code 5)5
M18 SOE flat closed end, external 222 O-ring
XK SOE plastic spring assembly, saw cut end
SI SOE metal spring/polypropylene cap, saw cut end

Table 4 - Gasket/O-ring materials

Code Gasket/O-ring materials
S Silicone
N Nitrile
E EPDM
V Fluorocarbon elastomer
4 Based on typical application usage.
5 For details, contact Pall Corporation.

적용분야

Waste reclaim, Wet etch & cleans

영역

Photovoltaics, Photovoltaics

Reviews

Earn 10% off* your next order online by leaving a review of this product. Please login to your account to leave a review. We appreciate and value your feedback.

*Subject to Terms and Conditions.