The Ultipleat® High Flow filter is a large diameter, coreless, single open ended, pleated cartridge with an inside-to-outside flow pattern. The filter's unique crescent-shaped pleat geometry, combined with its large 152.4 mm (6 inch) diameter and proprietary range of available Pall filter media, allows you to use significantly fewer filters and smaller housings for high flow rate applications. Systems can handle up to 115,443 lpm (30,500 gpm).
- Up to 50% smaller filter system possible
- Up to 40 times fewer elements to change out
- Higher flow rates per filter cartridge – up to 1900 lpm (500 gpm)
- Available in 508 mm (20 inch), 1016 mm (40 inch), 1524 mm (60 inch) and 2032 mm (80 inch) lengths
- Coreless, all plastic construction to minimize waste disposal
- Absolute rated filter medium for reproducible performance
- Inside-to-outside flow configuration – all debris stays within the filter
Materials of construction
|Filter Medium Filter Medium||Filter Medium||Support/Drainage Materials||End Caps||Wrap Materials|
|HDC® II Medium||High Area Polypropylene Structure||Polypropylene||Glass Filled Polypropylene||Polypropylene and Polyolefin Hotmelt|
|Profile® Medium in Ultipleat Format||Pleated Polypropylene Depth Structure||Polypropylene||Glass Filled Polypropylene||Polypropylene|
|Ultipor® GF Medium||Resin Bonded Glass Fiber / Polyester Support||Polyester / Nylon||Glass Filled Acetal||Polyester and Polyamide Hotmelt|
|Ultipleat CAS Medium||Pleated Polypropylene / Polyether Sulfone Membrane||Polypropylene||Glass Filled Polypropylene||Polypropylene|
|Polypropylene Medium/ CAS Composite Medium||Glass Fiber Medium2|
|Maximum Differential Pressure1 |
(normal inside to outside flow)
|3.4 bar at 82°C/ 50 psid at 180°F||3.4 bar at 121°C/ 50 psid at 250°F|
1) For fluids compatible with the filter element at the stated temperature.
2) Maximum temperature in aqueous systems is 60°C / 140°F.
Three configurations are available: horizontal6, vertical and centerpipe design.
The in-line horizontal configuration eliminates the need for a platform, or ladder, to remove the filters from the housing.
Vertical vessels may be more appropriate when floor space is limited. However, a platform may be needed to easily remove the elements.
In both the standard horizontal and vertical configurations, the inlet pipe is located between the filter element tubesheet and housing lid. The larger the vessel diameter, the longer the distance to reach in and remove the elements from the vessel. In a centerpipe vessel the housing lid is closer to the filter tubesheet. When the lid is opened the filters are easily accessible for installation and removal. Centerpipe vessels are larger in diameter, and more costly.
- Designed to the ASME, section VIII, division 1 code
- Maximum differential pressure across tubesheet: 5.17 bard (75 psid) maximum
- Standard housing gasket: spiral wound 304 stainless steel mineral fiber
- Carbon steel exterior surfaces: sandblasted and coated with an inorganic zinc
- Vent and drains: 1 inch FNPT
- Corrosion allowance: 1/8 inch
|Vessel Material||Tubesheet and Hold Down Plate Material of Construction||Pressure Rating in Barg/Psig at 60°C / 140°F|
|Carbon steel||304 stainless steel||18.95 bar (275 psig)|
|304 stainless steel||304 stainless steel||17.85 bar (259 psig)|
|304L stainless steel||304L stainless steel||14.89 bar (216 psig)|
|316 stainless steel||316 stainless steel||17.99 bar (261 psig)|
|316L stainless steel||316L stainless steel||14.89 bar (216 psig)|
Figure 1: Ultipleat High Flow Horizontal Housings (Aqueous Housing Pressure Drop)
Filter Cartridge Part Number = HFU   
|Code||Filter Dimensions, nominal, diameter (mm/in) x length (mm/in)||Suggested Maximum Water Flow Per Cartridge (lpm/gpm/mgd)|
|620||152.4/6 x 508/20||663/175/0.25|
|640||152.4/6 x 1016/40||1325/350/0.5|
|660||152.4/6 x 1524/60||1900/500/0.7|
|680||152.4/6 x 2032/80||1900/500/0.7|
Filter Cartridge Pressure Drop (typical) per Filter Length Shown2
1 The test procedure used is an adaptation of ISO 4572, modified to determine the micron size above which particles are quantitatively removed.
2 Multiply this value by the total system flow to determine the aqueous pressure drop. For fluids other than water, multiply this value by the fluid’s viscosity at the operating temperature in centipoise. This value is the pressure drop across the Ultipleat® High Flow filter(s) only; it must be added to the pressure drop contribution from the Ultipleat High Flow filter housing.
3 2 micron at 99% efficiency.
4 Precision evaluation of the 99.98% removal efficiency for these coarse grades is not possible with the ISO modified test procedure utilized. The removal efficiency was determined by the maximum spherical particle analysis.
|H13 (standard for glass fiber and aramid fiber filters)||Nitrile|
|J (standard for polypropylene filters)||Ethylene propylene|
|JU5||Ethylene propylene U-Cup|
5U-Cup seal is standard for the 1 micron composite filter.
Ordering Information-Standard Horizontal and Vertical Housings
Ordering Information - Horizontal Orientation, Centerpipe Designed Housings
7 For 60 inch filter lengths
|Code||Nominal cartridge length (mm/in)|
|285||Carbon steel vessel, 304 stainless steel tubesheet|
|S3||304L stainless steel|
|S8||304 stainless steel|
|L3||316L stainless steel|
|L8||316 stainless steel|
|Code||Optional outlet size8 horizontal housings|
|XU||Upper outlet location|
|XL||Lower outlet location|
8 If the housing is to be used as a prefiller to a horizontal liquid/liquid coalescer, then the vessel should be ordered using the XU or XL option for the outlet location. The orientation of the outlet should be the same as that of the sump on the coalescer. In this way no buildup of coalesced liquid will occur in the prefilter
Horizontal Housings, Centerpipe Design
Ultipleat High Flow Filter System Reduces Costs
Begin reducing your capital and operating costs today. Contact your local Pall distributor or call Pall directly for an Ultipleat High Flow filter system quotation.